Single or Dual Channel Digital Indicator		00
Features 6 digit red LED display One or two channels and third math channel Independent setup and scaling for all 3 channels 60/sec. Update Rate 20 point linearization Tare gross/net operation 18VDC 200mA excitation supply 1/8 DIN case NEMA 4X rated front No calculation scaling Calibrated load scaling Lockout with password Relay for alarm Shunt calibration Non-volatile memory Digital Filter - user selectable
.

Applications

• Process and/or strain gage
• Differential pressure measurement
• Torque, LVDT, strain gage, pressure transducer, and transmitter display
• Leak testing
• Peak/stress testing
• Pump/compressor monitor
• Bottle filling/weighing
• Level/volume display
• Differential flow measurement
• Production test monitoring

Standard Features

3 Types of Calibration
User - calibration allows the entry of the low and high input values and the corresponding low and high display engineering values.
Load - calibration allows setup via known input values. Simply apply the low input and set its corresponding display value, then apply the high input and set its value. The low and high values can be programmed at different times and then enabled.
Shunt - calibration allows setup via an external shunt calibrator resistor. Simply set the display low value and the shunt cal display value, then the meter will automatically measure the unloaded bridge for the zero value; then closes the internal shunt cal relay and measures the shunt calibrated input.

Autotare
This function allows the user to set the selected display/input to zero. It can be performed via a front panel key or remote input. Setup is available to switch the display from net to gross.

Net/Gross
The net value or the gross value can be displayed via a front panel key or remote input. Alarm limits, analog out or peak values may be assigned to the net or gross values.

Selectable Resolution / Sampling Rate
This unit has a selectable display resolution. You can select either 4 1/2 or 5 1/2 digit resolution both with an update rate of 60/sec.

Fine Offset
This allows for a direct zero offset to be programmed to compensate for system setups and changes.

Fine Scale
This allows for a direct correction of the span value without recalibrating.

20 Point Linearization
U-plot 20 point linearization allows the user to program up to 20 known values of nonlinear curvature along with the corresponding display readings. Typical uses are improved lineararity of transducers, load cells, etc. and for display of volume in irregularly shaped storage vessels.

Peak 1 and Peak 2
Peak 1 and peak 2 are both assignable to capture the maximum or minimum display value. They are assignable to any channel and the net or gross value.

Math Channel
The 4100 comes with an extra channel that is a non input channel. This can be used to duplicate an input channel for completely new scaling and alarm setups. The two channel input model 4100 can be used to perform A + B, A – B or A x B math functions. (Consult Precise Sensors Inc. for your special equations)

Second Scale
This function allows the user to set a second scaling to the input. The input will then be displayed in two engineering units (typically for English/Metric displays). Scale2 is setup by entering the input low and high values and corresponding display values.

Alarms
Each meter is standard with 4 programmable alarms that control the front panel LED status and the one standard relay and optional 3 relay outputs.

Each alarm is:

• Assignable to any channel
• Programmable for high or low limit
• Programmable setpoint value
• Programmable hysteresis for complete display range
• Programmable for latching
• Programmable to flash display on alarm
• Alarm #1 is programmable for fail safe operation for all the alarms. (Fail safe operation allows the relay to de-energize on loss of power.)

Relay Output
1 Form A relay 240VAC@5A, is provided standard for use as an alarm output or shunt cal relay.

Dummy Zero
Available soon

Option D: 3 each form C (single pole double throw) relays rated at 5 amp @ 240VAC, 5 amps @ 30VDC.

Option F: Excitation output voltage supplies (jumper selectable) 5VDC @ 40mA, 24 VDC @ 50mA, +15 VDC @ 200mA /supply, 10 VDC @ 200mA supply.

Option H: Analog output 0-5 VDC, 0-10 VDC, +5VDC to -5 VDC, 4-20mA, 0-20mA (Available soon)

Option K: Screw terminal connectors

• 1 required if no option board installed, 2 if option D, F, or H installed
• Accepts up to 14 Awg. Wire

Set up service: Factory scaling calibration (user provides input range and display range.)

Home