Precise Sensors Model 4000 data sheet

4000P
Process Meter - Current & Voltage
Our process meters can be set up with calibrated load inputs or one of the following easy and versatile selections. For process meters their pre-selected input ranges for 020mA, 4-20mA, 1-5VDC and 0-10VDC. Only the high and low display values are entered to scale the meter. For voltage meters the input selection is ± 10.5VDC. No calibration scaling is needed to display in engineering units. Simply enter the high and low input value and the corresponding high and low readings. This meter can also be set up with calibrated low inputs. For the current meter the input selection is ± 22.00mA and then the same set up routine as voltage.

4000S
Strain Gage/Load Cell Meter
Input selection from ±120mVDC. No Calculation scaling to display in engineering units. Simply enter low and high values and corresponding low and high reading. Meter can also be setup with calibration load inputs. Isolated 10VDC @ 30mA excitation supply.

Standard Features
Conversion
Microprocessor controlled charge balancing A/D converter with 18 bit internal resolution. Conversion rate selectable to 5/second on Process and Strain Gage meters.

4000P Volt Input
Input Range	0-10V, 1-5V setable from
±1.000V to ±10.500V	ranges
Accuracy	±0.04% f.s.
Zero Drift	±20 ppm/°C of f.s.
Span Drift	±50 ppm/°C of range
Input Impedance	>1 Mohm
Input Current	<10 nA
4000P Current Input
Input Range	0/40-20 setable from ±1 mA to ±20 mA ranges
Accuracy	0.05% f.s.
Zero Drift	±20 ppm/°C of f.s.
Span Drift	±50 ppm/°C of range
Input Resistance	<20 ohm
4000S Millivolt Input
Input Range	Setable range from ±30mVto ±120mV
Accuracy	±0.04% @ 100 mV
Zero Drift	±1uV°C + 20 ppm/°C of f.s.
Span Drift	±50 ppm/°C of f.s.
Input Impedance	>1000 Mohm
Input Current	<10nA
General Specifications
Input
N.M.R.R.	>60 dB @ 50 and 60Hz (without digital filter)
C.M.R.R.	>135 dB from input to supply
Response Time	1 second within ±0.05%
Conversion
Measuring System	Continuous integration charge balancing converter
Internal Resolution	1 part over 200,000
Conversion Time	Setable at 200, 400, 800,msec.
Digital Filter	Walking window mean setable as slow, normal or fast
Power Supply
AC Supply Voltage	90-264 ACV @ 47-70Hz
Power Consumption	4 VA
Isolation	>2500 Vrms
Environmental
Warmup Time	1 minute
Operating Temperature	-10/+60°C
Storage Temperature	-40/+85°C
Humidity	0/90% non-condensing
Mechanical
Front Protection	IP65/NEMA4
Dimensions	3/64 DIN; 0.94" x 2.83" x 4.5" (24 x 72 x 114.3 mm)
Case Material	Polycarbonate UL94V.2
Weight	0.4 pound - 200 g
Cut Out Dimensions	22H x 68W mm
Excitation Supply
4000P	24V ±5% @ 30 mA max. short circuit protected.
4000S	10V ±0.1% @ 30 mA max. short circuit protected and internal voltage trimming.
Alarm Output
Relay Output	250 ACV @ 5 A/24 DCV @ 1A
Options
Option: Analog Output
Current	0/4-20mA source
Load Resistance	0 to 550 ohm
Voltage	0-10V; output impedance 10 ohm
Accuracy	±0.1%
Isolation	500Vrms
Option: IR Probe and Setup Softwarex
Option: 1/8 DIN Adapter
Option: RS232 Printer Output
Voltage Level	V.24 compatible
Baud Rate	300, 600, 1200, 2400,4800, 9600
Isolation	200Vrms

4000P Process Signals Input Measuring Range
Input	Measuring Range	Display Range	Accuracy
Current	0-20 mA	-1999 to 9999	±0.05%
Voltage	0-10V	-1999 to 9999	±0.04%

4000S Load Cells and Strain Gage Input Measuring Range
Input	Measuring Range	Display Range	Accuracy
Voltage	From ±30.00 to 120 mV f.s.	-1999 to 9999	±0.04%

Process and Strain Gage Digital Indicator		00

Features 4 Digit LED Display 3/64 Din IP65/NEMA 4 Front Panel No Calculation Scaling Peak/Valley Tare Two Alarm Relay Output 85-264VAC Powered 5/Sec Display Update Rate Options: Analog Output, RS232 & Infra-Red Remote Setup
.